Canada's Well Water Guide
Loading regions
British Columbia • 272 Registered Wells

Lone Butte Water Well Depth & Hydrogeology

Regional groundwater summary • British Columbia Historical Log Extraction

Bottom Line Up Front

In Lone Butte, the median completed well is 143 ft deep.

A published hardness range for this place and aquifer is less than 10 to 180, and groundwater can exceed 1,000 mg/L as CaCO₃. That is a regional estimate, not a test of your well. Source: Estimate based on B.C. Ministry of Environment water-quality checks.

Most production draws from Bedrock (about 25% of local wells).

These municipal aggregates support planning only — they do not replace an accredited laboratory potability test for your own well.

Interactive Well Depth & Modeled Typical Strata

Drag the indicator line or tap a stratum below to read the recorded depth range

Drilling in: Sand & Gravel Aquifer (35–400+ ft)Glacial Drift Aquifer

Modelled Depth

143 FT

Area median

Drilling cost

$10,010–$21,450

Estimate

Published hardness

less than 10 to 180, and groundwater can exceed 1,000 mg/L as CaCO₃

0 ft (Surface)Median 143 ft400 ft (Deep)
Topsoil & Surficial Organics
Glacial Drift Silt & Till
Sand & Gravel Aquifer
Modeled typical strata:

Modeled typical strata — placeholder from median depth + aquifer type; not local driller logs.

Well Statistics

Local measurements compared against British Columbia provincial benchmarks.

Total Registered Wells 272
Median Well Depth 143 ft
BC benchmark: 162 ft provincial median
Average Well Depth 161.5 ft
Dominant Aquifer Bedrock
Hardness less than 10 to 180, and groundwater can exceed 1,000 mg/L as CaCO₃ — Estimate. Estimate based on B.C. Ministry of Environment water-quality checks
Drilling cost $10,010–$21,450 — Estimate. Typical drilling prices in Canada, about $70–$150 per foot
Domestic Household Use 89% of wells

Where This Report Applies

Approximate boundary of Lone Butte

Shaded area is an approximate municipal outline for orientation only. Well records are aggregated across the entire Lone Butte.

Depth Distribution

Most completed wells fall near the median depth of 143 ft. Recorded depths cover 267 wells.

0–49 ft 6% · 16
49–98 ft 16.1% · 43
98–148 ft 28.5% · 76
148–197 ft 21% · 56
197–295 ft 20.2% · 54
295–394 ft 6.4% · 17
394–591 ft 1.9% · 5
591+ ft 0% · 0

Median depth of 143 ft falls inside the reported range. Deeper completions here usually mean higher mineral content but steadier year-round pressure.

Aquifer Composition

Bedrock and drift aquifers recorded by drillers in this area. Recorded for 91 of these 272 wells.

Carbonate Bedrock (Limestone / Dolomite) Primary Bedrock Aquifer
24.6%

67 of 272 Major regional bedrock aquifer formed by Ordovician/Silurian dolomite. Known for reliable, high-volume yields with elevated mineral hardness and dissolved calcium/magnesium carbonates.

Undifferentiated Aquifer Regional Formation
8.8%

24 of 272 Unclassified hydrogeological formation from legacy provincial drill records.

5 holes found no usable water. test holes, observation or monitoring wells, dewatering wells, decommissioned wells, dry holes, no-aquifer holes, and other non-supply wells filtered out of the headline

Water Quality Profile

A published hardness range, when one exists for this place and aquifer. Not a test of your well.

Measured nearby

Measured government tests within 25 km of Lone Butte.

Soft (<60) Med (61–120) Hard (121–180) V. hard (>180)

USGS (2018) bands reprinted by Health Canada. A range can cross more than one band. This is not a sample.

What this is not

  • Not a laboratory result for a well on your property.
  • Not a reason to size a softener. Size equipment from a lab test.
  • Not a drilling quote. A cost line on this page is a national estimate, not a price for one well.

Health Canada has not set a maximum acceptable concentration for hardness. A wide published range can sit in more than one USGS band.

OBS WELL 78 - LONE BUTTE NEAR RAIL STATION, 13.42 km away, in the wider area.

3 government lab tests, dated 1988–2005.

These results are old (tested 1988–2005).

Hardness 180–341 mg/L as CaCO₃, median 300.1.

Worked out by wellwaterguide.ca from 3 government lab tests.

reported hardness, or calculated from measured calcium and magnesium when hardness was not reported

BC Environmental Monitoring Data System (EnMoDS) results: Provincial Groundwater Observation Well Network wells Open Government Licence - British Columbia

Drilling Activity

Historical permit and construction activity by decade.

Pre-1970 4 wells
1970s 10 wells
1980s 16 wells
1990s 7 wells
2000s 37 wells
2010s 68 wells
2020s 81 wells

Treatment

Size treatment from a laboratory test

This page does not turn a hardness range or a well depth into an equipment total, a grain capacity, or a drilling price. Read the methodology, the filtration guide, and the products catalog.

Suggested system

Suggested system for Lone Butte

1

Test kit

estimate, confirm with a lab test

A test of your own well comes before any equipment. Test for coliform bacteria.

Water testing
2

Iron and manganese filter

estimate, confirm with a lab test

Manganese above the aesthetic objective, consider an iron/manganese filter. A monitoring well near this place has median manganese of 0.05 mg/L.

Iron and manganese guide
3

Water softener

estimate, confirm with a lab test

A softener is likely needed. The nearest monitoring well has a median hardness of 300.1 mg/L as CaCO₃.

Hard-water guide
Local Contractors

Licensed Water Well Drillers Serving Lone Butte

Because water wells in Lone Butte average 143 ft into bedrock, contractors equipped with heavy rotary rigs and proper casing seals are recommended. Contact local drillers directly or request competitive bids.

Bud’s Water Wells Ltd.

Yard: Kamloops, BC (122 km away)

Confirm the contractor's provincial licence before you hire
Interior BC Bedrock Submersible Pumps Pressure Tanks
(250) 573-3000

Aqua Source Drilling

Yard: Vernon, BC (192.3 km away)

Confirm the contractor's provincial licence before you hire
Okanagan Aquifers Deep Sand & Gravel Domestic Wells
(250) 275-0920

Cariboo Water Wells Ltd.

Yard: Prince George, BC (274.6 km away)

Confirm the contractor's provincial licence before you hire
Northern BC Formations Large Diameter Casing Well Screens
(250) 564-2525

A & H Drilling Ltd.

Yard: Chilliwack, BC (277 km away)

Confirm the contractor's provincial licence before you hire
Dual Rotary Drilling Agricultural Irrigation Domestic Wells
(604) 794-5544

Looking for more regional well drillers?

Explore all registered water well contractors operating across BC.

All BC Drillers →

Featured Contractor Spot

Are you a licensed well driller serving Lone Butte?

Claim your verified listing profile and be found by homeowners on this report.

Claim Local Listing

Frequently Asked Questions

Quick answers about water wells in Lone Butte.

What is the median well depth in Lone Butte?

Among 267 producing water wells with a recorded depth, the median is 143.0 ft (43.59 m).

Which aquifer is recorded most often in Lone Butte?

The most frequently recorded producing aquifer is Bedrock, on 67 of 91 wells with a producing aquifer name.

Adjacent Municipalities & Nearby Well Records

Explore neighbouring hydrogeological formations and compare drilling depths

Horse Lake

8.3 km

View well logs →

Sheridan Lake

12.3 km

View well logs →

Deka Lake

13 km

View well logs →

100 Mile House

17.3 km

View well logs →

Forest Grove

19.1 km

View well logs →

Nearby communities